Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to experienced auto locksmiths who have the appropriate equipment and technical knowledge. They can design and program keys quicker and more efficiently than dealerships.

If the key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. However, there are many other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will hinder your Peugeot 208 from locking or workshop unlocking and won't start the engine. In this instance you'll need employ the alternate method of starting described in your vehicle owner's manual.

Another reason your 208 might not start is because the spark plugs are been worn down. The spark plugs are responsible for instigating the fuel that ignites the engine. They are only able to last for a short time. If they aren't used enough they will eventually fail.

Luckily, there is an easy solution to this issue. The best solution is to determine the voltage of your car battery using a multimeter. If it's less than 11.5 Volts it is time to replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by lifting the rubber covers that protect the two terminals of the battery and using a wire brush to remove any parts that are corroded from the battery. It is then time to reconnect the cables to the positive and negative poles.

Water Damage

If your 208 will not start and the battery has not failed, you should inspect the spark plugs. It could be that they're overly filthy, making them unable to spark. This can be fixed easily by cleaning the spark plugs in a workshop.

Peugeot cars have a transponder key that works with the car's ignition system. This ensures that only the correct key can turn the engine. If the chip inside the peugeot 207 car key key is damaged, then it won't transmit the proper signal to the vehicle.

This is a frequent issue that can occur due to water damage. This is especially prevalent in colder climates, where the vehicle could have been exposed to snow or rain. If this is the case, get in touch with a reputable locksmith who has all the tools and equipment required to change the key's programming. They will also have all the latest technology and machinery needed to make the Peugeot smart key. The process should not take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that incorporates electronic components that are placed on a circuit board. This new system works great when it's fresh, however, over time, the circuit boards start to degrade and stop working properly.

This can stop the immobiliser chip from activating and causing your car to not start. If this happens, it's recommended to call a Peugeot specialist or locksmith.

Another issue that is common is when the battery in the key fob starts to die, this causes the blade of the key to stop from entering the lock. A locksmith for cars can replace the battery and cut a new blade for you, it's usually a simple fix.

Faulty Receiver Module

It could be that the receiver module is defective in the event that your Peugeot key fob doesn't work after being dropped on the floor, exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer that controls the central locking system of your peugeot 206 key replacement vehicle.

The key fob itself is fitted with rubber seals which prevent water from reaching the chip inside. However prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. The high salt content of the ocean water or pool could cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This is only done by an expert auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the correct code to begin the car. This is why you should go with a knowledgeable Peugeot locksmith to handle the task of designing and programming an appropriate replacement.

Faulty On-Board Computer

The computer on board in your Peugeot is responsible for many of the systems in your vehicle, from airbags to power windows. The on-board computer will show an error code when something goes wrong. This code is saved in the system and will remain there until the issue has been resolved. This can often mean that the on-board computers to be replaced.

The most frequent cause for the airbag warning light to turn on is corrosion or loose connections within the sensor. This could be due to wear and tear, age or exposure to moisture and salt. This issue should be addressed as soon as you can, as an airbag that is not functioning could be dangerous in the event in the event of an accident.

If your Peugeot is showing a card that is not being detected error then the key battery inside the key fob could be weak or dead. This will stop the key fob sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this fails, the key battery has to be replaced.