Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it might be time to replace the battery. If you replace the battery, but it's still not working the issue could be somewhere else.

At United Locksmith, we specialize in making new keys for old automobiles. We have the tools and parts needed for this service.

Dead Coin Battery

A dead battery is the main cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob comes with an in-built battery that is prone to draining quickly in the event that it is not used often enough. If your remote started to show signs of weakness such as a loss of range and then completely stopped working the battery could be dead.

Metal clips keep the battery securely inside the key fob. If the clips are not tight, they can cause contact issues that prevent the remote from receiving power. Use a flathead screwdriver to open the retaining clips and remove the battery. Choose a battery that is the same size, voltage and specification as the original.

Exposure to water can cause the key fob to become corroded or damaged. Even a quick bath in warm, soapy water could cause damage to the chip. Keep your key fob dry.

Water Damage

If your key fob doesn't work properly, pro.po.s.a.l.s.cv.h it could be caused by water damage. The rubber seals on key fobs prevent them from getting damaged by a small splash or drizzle of water. However, it's important to keep the keys of your car away from the ocean, washing machine, and pool.

The key fob comes with an electronic chip that transmits an immobilizer system of your vehicle. The chip is what allows the 500 to lock and start. If it gets wet, however, it will no longer function.

If you're interested in checking if your key fob is still working you can clean the internal electronics using isopropyl or an electronic cleaner. It is recommended to replace a key fob in the event that it's submerged in salt water rather than try to fix it yourself.

While a replacement fob might cost a little money, it's a lot cheaper than paying for your Fiat 500 to be towed to the dealer and repaired! You can also make it yourself with some simple steps. Be sure to use the correct battery type before you attempt to open your key fob. You can find step-bystep instructions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob communicates with the vehicle's immobiliser to ensure that the vehicle is only capable of starting when the correct key is used. If the chip is damaged, or damaged in any way your car will not start.

Damage to the water or a dead battery are the most frequent causes of the chip being damaged. It is best to leave the work to a professional locksmith who can repair the chip in a short time and at a an affordable price.

If your key fob does not work after exposure to clean water from a tap or rain take the battery off. Clean the electronic component with a towel. If the key fob doesn't work it's most likely a fried chip and will need to be replaced.

A few people will visit their dealer if they need a new fiat punto replacement key fob. But, this can be an expensive option. If you're looking for a low-cost solution to get your Fiat key fob fixed, look no further than United Locksmith. We have all the tools and expertise to fix your fiat 500 replacement key near me fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs transmit an electronic signal to the vehicle that will unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. There are a variety of reasons why a fob could stop working. It could be due to a dead battery damaged by water buttons, worn out buttons or a problem with the receiver module, and signal interference or a malfunctioning electronic chip.

If the fob is in an area that has experienced severe trauma (such as being dropped on the floor or vehicle washed in the washer) the fob may not be able to connect with the Body Control Module (BCM) of the vehicle. This is because the BCM is secured and will only accept a signal from a genuine key and not another.

You'll need to replace the fob in case this occurs. A professional locksmith is able to handle every aspect of the replacement procedure as well as programming a new one for the 500. They can even give you an clone fob that performs exactly the same way as the original (and costs only one-third of the cost).